 |
揚州市昂立電氣有限公司
主營產品： 單級滑觸線,工字鋼電纜滑車,滑線指示燈,電纜滑線導軌,滑線集電器,無接縫滑觸線 |
會員.png)
聯系電話
13813192852
公司信息
- 聯系人：
- 梁先生
- 電話：
- 0514-89797910
- 手機：
- 13813192852
- 傳真：
- 0514-89799820
- 地址：
- 揚州市邗江區工業園區
- 郵編：
- 225126
- 個性化：
- www.yibao17.com
- 網址：
- www.yibao17.com
闡述行車滑觸線容易出現的故障及解決辦法
2015-10-19 閱讀(836)
1、導電器行走有較大異響。會出現接頭不平整的現象，這時我們就要重新安裝導軌連接。
1, guide electrical walk has great sound. There will be a joint uneven phenomenon, then we're going to reinstall the guide rail connection.
2、工作時導軌晃動大。出現這個問題的原因可能是導軌整線直線度較差；懸吊夾松動；解決這兩種現象的方法就是調整導軌直線度以及擰緊懸吊夾螺釘。
2, work the guide shook. The reasons for this problem may be the guide the whole line straightness is poorer; Loose suspension clamp; The solution to the two phenomena is to adjust the guide rail straightness and tighten the suspension clamp screw.
3、電刷磨損快。出現這個問題的原因可能是接頭不平整；載流量過大；彈簧壓力過大。那么我們可以按要求重新連接導軌，增加導電器數量以及更換、修正彈簧壓力。
3, brush wear quickly. The reasons for this problem may be uneven joint; Carrying capacity is too large; Spring pressure is too large. So we can reconnect the guide rail, according to the requirement to increase the number of guide electric appliance and change, fixed spring pressure.
4、導軌內有火花?？赡苁且?yàn)殡娝⒈砻媾c導軌接觸不良以及電流過大。這時我們就要檢查導軌接頭，讓它適當磨合電刷，保證6０％接觸面積。同時也可以增加電器數量。
4, guide rail with spark. May be because the brush surface and guide poor contact and current is too large. Then we will check the rail joint, let it properly running-in brush, guarantee 60% contact area. At the same time also can increase the number of electrical appliances.
